Ti Alloy Gr 2 Dome Washers, Titanium Gr 2 Lock Washers, UNS R50400 Fender Washer, Titanium Alloy Gr 2 Square Washer, 3.7035 Belleville Washers, Titanium Gr 2 Ogee Washers, Titanium Gr 2 Split Washers, Ti Alloy Gr 2 Tooth Lock Washer Stockist Supplier in Mumbai, India.
Typical warmness remedy entails answer remedy and Quenching. At this point, the shape stays austenitic. Martensitic transformation is then received both via way of means of a cryogenic remedy at −75 Degree C (−103 Degree F) or via way of means of severe cold work (over formation, normally via way of means of cold rolling or twine drawing). Its aging is done at 510 Degree C (950 Degree F) — which precipitates the Ni3Al intermetallic phase — is accomplished as above on almost completed elements.Typical heat remedy entails solution remedy and quenching in Titanium WNR 3.7035 Lock Washers, accompanied via way of means of ageing at 715 Degree C (1,319 Degree F). Aging bureaucracy Ni3Ti precipitates and will increase the yield strength to approximately 650 MPa at room temperature.
It does now no longer go through uniform corrosion while uncovered to moist environments. Unprotected carbon metallic rusts with ease while uncovered to an aggregate of air and moisture. The ensuing iron oxide floor layer is porous and fragile.The complete floor of the metallic is attacked, and the corrosion is expressed as corrosion rate. Unlike the other grades, the mechanical properties and creep resistance of this Titanium UNS R50400 Machine Washers continue to be superb at temperatures as much as 700 Degree C (1,292 Degree F). As a result, it's far categorized as a Fe-primarily based totally superalloy, utilized in jet engines, fueloline turbines, and faster elements.
Material Specification Chart of Titanium Gr 2 Washers
| Specification | ASTM B348 / ASME SB348 |
|---|---|
| Size | M02 to M33, Custom Sizes |
| Length | 3 mm to 200 mm |
| Washer | UNF, BSW, BSF, METRIC, UNC, or as required |
| Standard of Washers | DIN 125A, DIN 125B, DIN 127B, DIN 137B, DIN 6797A, DIN 6797J, ISO 7089, DIN 7980, DIN 127 B, IS 2016, ASTM F436M, ASME B18.13, ASME B18.21.1, ASME B18.22.1, ASME B18.23.1 |
| Form of Washers | Hex, Threading, Square, Round as per Gauge Etc. |
| Raw materials Source | JSPL, Mukund Steel, Tata Steel, Dhamm Steel, Usha Martin, etc. |
| Threads Configuration | ASME B1.1 2A/3A – 2B/3B Inch Unified Threads and B1.13M 6h-6G Metric Coarse Threads |
| Certification | Dual Certified As per ASTM & ASME Codes |
| Threads | Unless otherwise specified, the threads shall be rolled or cut and tapped horizontally or vertically |
| Test Certificate of Washers | as per EN 10204 / 3.1 Manufacturer Test Certificate |
| Additional Certifications | PED 97/23/EC Certified, Merkblatt AD 2000 W2 Certified |
| Production process | M24-M100: hot forging, M2-M24: Cold Froging, for custom-made connecting element machining and CNC |
| Head drive of Washers | Six-Lobe, Phillips, Phillips/Slot, Slotted etc |
| Packing of Washers | IN BULK: canton, pallet, Small Boxs / carton / pallet, or customer request |
| Surface Coating | Ptfe Coated Washers Phosphate Coating Teflon Coating Zinc Coating Hot Dipped Galvanizing Coating Cadmium Coating Xylon Coating |
| Types | Plain / Flat Washer, Spring Washers, Dome Washer, Hexagonal Washer, Square Washer, Dome Tooth Washer, Countersunk Washer, Tooth Lock Washer, Dock Washer, Fender Washer, Ogee Washer, Hex Washers, Split / Lock Washer, Customized Washer, Tab Washers |
Various Types Of Titanium Gr 2 Washers
Titanium Gr 2 Flat Washers
- ASME SB348 Titanium Alloy Gr 2 Knurled Flat Washer
- Ti Alloy Gr 2 Flat Washer
- 3.7035 Flat Washer
- ASTM B348 Titanium Gr 2 Thick Flat Washer
- UNS R50400 Plain Washer
- Titanium Gr 2 Thin Flat Washer
Titanium Gr 2 Ogee Washers
- ASME SB348 Titanium Alloy Gr 2 Thin Ogee Washer
- Ti Alloy Gr 2 Ogee Washer
- UNS R50400 Ogee Washer
- Titanium Gr 2 Thick Ogee Washer
- ASTM B348 Titanium Gr 2 Ogee Washer
- 3.7035 Ogee Washer
Titanium Gr 2 Lock Washers
- Titanium Alloy Gr 2 Lock Washer
- ASME SB348 Titanium Alloy Gr 2 Split Lock Washer
- 3.7035 Internal Tooth Lock Washer
- UNS R50400 Lock Washer
- Titanium Gr 2 Lock Washer
- ASTM B348 Titanium Gr 2 Heavy Duty Lock Washers
Titanium Gr 2 Spring Washers
- Titanium Gr 2 Wave Spring Washer
- 3.7035 Helical Spring Washer
- ASME SB348 Titanium Gr 2 Flat Spring Washer
- UNS R50400 Spring Washers
- Titanium Alloy Gr 2 Spring Washers
- ASTM B348 Ti Alloy Gr 2 Spring Washer
Titanium Gr 2 Star Washers
- UNS R50400 Internal Star Washer
- ASME SB348 Titanium Alloy Gr 2 Spring Washer
- 3.7035 Spring Washer
- ASTM B348 Ti Alloy Gr 2 Spring Washer
- Titanium Alloy Gr 2 External Star Washer
- Titanium Gr 2 Star Spring Washer
Titanium Gr 2 Fender Washers
- Titanium Gr 2 Fender Washer
- ASME SB348 Ti Alloy Gr 2 Fender Washer
- ASTM B348 Titanium Alloy Gr 2 Standard Fender Washer
- Titanium Gr 2 Spring Steel Fender Washer
- UNS R50400 Heavy Duty Fender Washer
- 3.7035 Fender Washer
Equivalent Grades of Titanium Gr 2 Washers
| STANDARD | UNS | WERKSTOFF NR. |
| Titanium Gr 2 | R50400 | 3.7035 |
View Size Table Of Titanium Gr 2 Washers, We have Global sales network for Titanium Alloy Gr 2 Plain Washer, Wide Stockist Of Werkstoff No 3.7035 Spring Washers In India.
Size Chart of Titanium Gr 2 Washers
| Size | USS | SAE | ||||
|---|---|---|---|---|---|---|
| Inside Diameter (A) |
Outside Diameter (B) |
Thickness (C) |
Inside Diameter (A) |
Outside Diameter (B) |
Thickness (C) |
|
| #2 | – | – | – | 3/32″ | 1/4″ | 0.020″ |
| #4 | – | – | – | 1/8″ | 5/16″ | 0.032″ |
| #6 | – | – | – | 5/32″ | 3/8″ | 0.049″ |
| #8 | – | – | – | 3/16″ | 7/16″ | 0.049″ |
| #10 | – | – | – | 7/32″ | 1/2″ | 0.049″ |
| #12 | – | – | – | 1/4″ | 9/16″ | 0.065″ |
| 1/4″ | 5/16″ | 0.734″ | 0.065″ | 9/32″ | 5/8″ | 0.065″ |
| 5/16″ | 3/8″ | 7/8″ | 0.083″ | 11/32″ | 11/16″ | 0.065″ |
| 3/8″ | 7/16″ | 1″ | 0.083″ | 13/32″ | 13/16″ | 0.065″ |
| 7/16″ | 1/2″ | 1-1/4″ | 0.083″ | 15/32″ | 15/16″ | 0.065″ |
| 1/2″ | 9/16″ | 1-3/8″ | 0.109″ | 17/32″ | 1-1/16″ | 0.095″ |
| 9/16″ | 5/8″ | 1-15/32″ | 0.109″ | 19/32″ | 1-5/32″ | 0.095″ |
| 5/8″ | 11/16″ | 1-3/4″ | 0.134″ | 21/32″ | 1-5/16″ | 0.095″ |
| 3/4″ | 13/16″ | 2″ | 0.148″ | 13/16″ | 1-15/32″ | 0.134″ |
| 7/8″ | 15/16″ | 2-1/4″ | 0.165″ | 15/16″ | 1-3/4″ | 0.134″ |
| 1″ | 1-1/16″ | 2-1/2″ | 0.165″ | 1-1/16″ | 2″ | 0.134″ |
| 1-1/8″ | 1-1/4″ | 2-3/4″ | 0.165″ | – | – | – |
| 1-1/4″ | 1-3/8″ | 3″ | 0.165″ | – | – | – |
| 1-3/8″ | 1-1/2″ | 3-1/4″ | 0.180″ | – | – | – |
| 1-1/2″ | 1-5/8″ | 3-1/2″ | 0.180″ | – | – | – |
| 1-5/8″ | 1-3/4″ | 3-3/4″ | 0.180″ | – | – | – |
| 1-3/4″ | 1-7/8″ | 4″ | 0.180″ | – | – | – |
| 2″ | 2-1/8″ | 4-1/2″ | 0.213″ | – | – | – |
Check available Sizes of ASME SB 348 Titanium Gr 2 Washers, Ask For Ready Stock of UNS R50400 Washers in Mumbai, India.
BAGODA
Quick Contact
Dimensions of Titanium Gr 2 Spring Washer
| NOM SIZE | Inner Dia (d) Basic Tol (+) | Outer Dia (d1) Max | WIDTH (b) Basic Tol (+ or -) | THICKNESS (S) Basic Tol (+ or -) | Weight per 1000 in Kgs | |||
| 3 | 3.1 | 0.3 | 6.2 | 1.3 | 0.1 | 0.8 | 0.1 | 0.11 |
| 4 | 4.1 | 0.3 | 7.6 | 1.5 | 0.1 | 0.9 | 0.1 | 0.18 |
| 5 | 5.1 | 0.3 | 9.2 | 1.8 | 0.1 | 1.2 | 0.1 | 0.36 |
| 6 | 6.1 | 0.4 | 11.8 | 2.5 | 0.15 | 1.6 | 0.1 | 0.83 |
| 8 | 8.1 | 0.4 | 14.8 | 3 | 0.15 | 2 | 0.1 | 1.60 |
| 10 | 10.2 | 0.5 | 18.1 | 3.5 | 0.2 | 2.2 | 0.15 | 2.53 |
| 12 | 12.2 | 0.5 | 21.1 | 4 | 0.2 | 2.5 | 0.15 | 3.82 |
| 14 | 14.2 | 0.5 | 24.1 | 4.5 | 0.2 | 3 | 0.15 | 6.01 |
| 16 | 16.2 | 0.8 | 27.4 | 5 | 0.2 | 3.5 | 0.2 | 8.91 |
| 18 | 18.2 | 0.8 | 29.4 | 5 | 0.2 | 3.5 | 0.2 | 9.73 |
| 20 | 20.2 | 1 | 33.6 | 6 | 0.2 | 4 | 0.2 | 15.20 |
| 22 | 22.5 | 1 | 35.9 | 6 | 0.2 | 4 | 0.2 | 16.50 |
| 24 | 24.5 | 1 | 40 | 7 | 0.25 | 5 | 0.2 | 26.20 |
| 27 | 27.5 | 1 | 43 | 7 | 0.25 | 5 | 0.2 | 28.70 |
| 30 | 30.5 | 1.2 | 48.2 | 8 | 0.25 | 6 | 0.2 | 44.30 |
| 33 | 33.5 | 1.2 | 55.2 | 10 | 0.25 | 6 | 0.2 | 63.00 |
| 36 | 36.5 | 1.2 | 58.2 | 10 | 0.25 | 6 | 0.2 | 67.30 |
| 39 | 39.5 | 1.2 | 61.2 | 10 | 0.25 | 6 | 0.2 | 71.70 |
| 42 | 42.5 | 1.2 | 68.2 | 12 | 0.25 | 7 | 0.25 | 111.00 |
| 45 | 45.5 | 1.2 | 71.2 | 12 | 0.25 | 7 | 0.25 | 117.00 |
| 48 | 49 | 1.5 | 75 | 12 | 0.25 | 7 | 0.25 | 123.00 |
| 52 | 53 | 1.5 | 83 | 14 | 0.25 | 8 | 0.25 | 320.00 |
Dimensions of Titanium Gr 2 Flat Washer
| Bolt Size | USS | SAE | ||||
| OD (in.) | ID (in.) | Thickness | OD (in.) | ID (in.) | Thickness | |
| 1/8 (#6) | – | – | – | 0.375 | 0.156 | .036/.065 |
| 5/32 (#8) | – | – | – | 0.438 | 0.188 | .036/.065 |
| 3/16 (#10) | 0.560 | 0.250 | .036/.065 | 0.500 | 0.220 | .036/.065 |
| 7/32 (#12) | – | – | – | 0.562 | 0.250 | .051/.080 |
| 1/4 (#14) | 0.734 | 0.312 | .051/.080 | 0.625 | 0.281 | .051/.080 |
| 5/16 | 0.875 | 0.375 | .064/.104 | 0.688 | 0.344 | .051/.080 |
| 3/8 | 1.000 | 0.438 | .064/.104 | 0.812 | 0.406 | .051/.080 |
| 7/16 | 1.250 | 0.500 | .064/.104 | 0.922 | 0.469 | .051/.080 |
| 1/2 | 1.375 | 0.562 | .086/.132 | 1.062 | 0.531 | .074/.121 |
| 9/16 | 1.469 | 0.625 | .086/.132 | 1.156 | 0.594 | .074/.121 |
| 5/8 | 1.750 | 0.688 | .108/.160 | 1.312 | 0.656 | .074/.121 |
| 3/4 | 2.000 | 0.812 | .122/.177 | 1.469 | 0.812 | .108/.160 |
| 7/8 | 2.250 | 0.938 | .136/.192 | 1.750 | 0.938 | .108/.160 |
| 1 | 2.500 | 1.062 | .136/.192 | 2.000 | 1.062 | .108/.160 |
| 1 1/8 | 2.750 | 1.250 | .136/.192 | 2.250 | 1.250 | .108/.160 |
| 1 1/4 | 3.000 | 1.375 | .136/.192 | 2.500 | 1.375 | .136/.192 |
| 1 3/8 | 3.250 | 1.500 | .153/.213 | 2.750 | 1.500 | .136/.213 |
| 1 1/2 | 3.500 | 1.625 | .153/.213 | 3.000 | 1.625 | .153/.213 |
| 1 5/8 | 3.750 | 1.750 | .153/.213 | – | – | – |
| 1 3/4 | 4.000 | 1.875 | .153/.213 | – | – | – |
| 1 7/8 | 4.250 | 2.000 | .153/.213 | – | – | – |
| 2 | 4.500 | 2.125 | .153/.213 | – | – | – |
| 2 1/4 | 4.750 | 2.375 | .320/.248 | – | – | – |
| 2 1/2 | 5.000 | 2.625 | .210/.280 | – | – | – |
| 2 3/4 | 5.250 | 2.875 | .228/.410S | – | – | – |
| 3 | 5.500 | 3.125 | .249/.327 | – | – | – |
Weight Chart Of Titanium Gr 2 Washers
| APPROX. WEIGHT IN KGS FOR 100 NOS | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| SIZE | PLAIN PUNCHED WASHER IS:2016 |
HEAVY WASHER IS:6610 |
MACHINED WASHER IS:2016 |
SQUARE | TAPER | WASHERS | SPRING WASHER FLAT SECTION IS:3063-72 | SPRING WASHER SQUARE SECTION IS:6735-72 DIN : 7980 |
Size (Inches) | PLAIN PUNCHED WASHER BS:3410 TABLE 7 |
|||
| MACHINED | HIGH STRENGTH FRICTION GRIP |
||||||||||
| FOR CHANNELS IS:5372-75 |
FOR I-BEAM IS:5374-75 |
TYPE-B (CHANNELS) IS : 6649-85 |
TYPE-C ( I-BEAMS ) IS : 6649-85 |
||||||||
| M-3 | 0.01 | 0.01 | |||||||||
| M-4 | 0.02 | 0.02 | |||||||||
| M-5 | 0.04 | 0.04 | 0.03 | 0.03 | |||||||
| M-6 | 0.11 | 0.11 | 0.08 | 0.04 | 1/4″ | 0.21 | |||||
| M-8 | 0.20 | 0.21 | 1.10 | 1.20 | 0.16 | 0.11 | 5/16″ | 0.35 | |||
| M-10 | 0.39 | 1.60 | 0.40 | 1.00 | 1.10 | 0.25 | 0.20 | 3/8″ | 0.48 | ||
| M-12 | 0.58 | 1.90 | 0.62 | 2.00 | 2.20 | 2.00 | 1.80 | 0.38 | 0.23 | 1/2″ | 1.07 |
| M-14 | 0.82 | 0.60 | 0.38 | ||||||||
| M-16 | 1.06 | 2.90 | 1.13 | 3.40 | 3.75 | 9.00 | 8.50 | 0.89 | 0.59 | 5/8″ | 1.85 |
| M-18 | 1.27 | 0.97 | 0.66 | ||||||||
| M-20 | 1.64 | 4.40 | 1.72 | 5.80 | 6.70 | 8.50 | 8.00 | 1.52 | 1.23 | 3/4″ | 2.91 |
| M-22 | 1.75 | 7.50 | 7.00 | 1.65 | 1.36 | 7/8″ | 4.27 | ||||
| M-24 | 3.11 | 6.30 | 3.30 | 13.50 | 16.00 | 6.50 | 6.00 | 2.62 | 1.81 | 1″ | 6.13 |
| M-27 | 3.94 | 8.00 | 4.23 | 12.50 | 15.00 | 12.00 | 11.50 | 2.87 | 2.06 | 1.1/8″ | 7.69 |
| M-30 | 5.05 | 10.10 | 5.36 | 16.50 | 18.70 | 17.50 | 16.00 | 4.43 | 3.20 | 1.1/4″ | 9.90 |
| M-33 | 7.10 | 12.00 | 7.54 | 21.00 | 23.50 | 23.00 | 22.50 | 6.30 | 3.50 | ||
| M-36 | 8.73 | 14.60 | 9.20 | 25.50 | 29.20 | 26.50 | 26.00 | 6.73 | 5.25 | 1.1/2″ | 17.24 |
| M-39 | 12.60 | 16.70 | 13.30 | 28.30 | 34.50 | 7.17 | 5.61 | ||||
| M-42 | 17.50 | 20.10 | 18.30 | 11.10 | 8.00 | ||||||
| M-45 | 21.20 | 22.20 | 22.00 | 11.70 | 8.53 | ||||||
| M-48 | 28.40 | 26.00 | 29.40 | 12.30 | 9.00 | 2″ | 27.78 | ||||
| M-52 | 31.90 | 33.00 | 18.20 | ||||||||
| M-56 | 47.90 | 19.30 | |||||||||
| M-60 | 51.60 | 20.30 | |||||||||
| M-64 | 55.40 | 21.80 | |||||||||
| M-68 | 57.40 | ||||||||||
| M-72 | 63.40 | 24.00 | |||||||||
Ready Stock Titanium Gr 2 Washers
- Titanium Alloy Gr 2 Hexagonal Washer
- Titanium Alloy Gr 2 Customized Washer
- Titanium Gr 2 Dome Tooth Washer
- Titanium Alloy Gr 2 Conical Spring Washer
- UNS R50400 Washers
- Titanium Gr 2 Customized Washer
- Titanium Gr 2 Split / Lock Washer
- JIS NCF Gr 2 Tooth Lock Washer
- ASTM B348 Titanium Gr 2 Dome Washer
- Titanium Gr 2 Hexagonal Washer
- Ti Alloy Gr 2 Split Washer
- Titanium Gr 2 Tab Washer Exporter
- 3.7035 Machine Washer
- Ti Alloy Gr 2 Spring Washers Distributor
- Ti Alloy Gr 2 Cup Washer
- Titanium Gr 2 Industrial Washers
- Titanium Alloy Gr 2 Belleville Washers
- Titanium Gr 2 Punched Washer
- Titanium Alloy Gr 2 Hex Washers
- Ti Alloy Gr 2 Hex Washers
- Ti Alloy Gr 2 Countersunk Finishing Washer
- Ti Alloy Gr 2 Square Washer
- Titanium Alloy Gr 2 Flat Washer
- Ti Alloy Gr 2 Finishing Washers
- Titanium Alloy Gr 2 Square Washer Manufacturer
- Titanium Alloy Gr 2 Split Ring Washer
- Titanium Alloy Gr 2 Plain Washer Supplier in Mumbai
- Titanium Alloy Gr 2 Flat Washer Stockist
- Titanium Gr 2 Spring Washers
- Titanium Gr 2 Dock Washer
- ASTM B348 Titanium Gr 2 Wave Washer
- Titanium Gr 2 Spring Washers
- ASTM B348 Titanium Gr 2 Washers
- Titanium Gr 2 Star Washers
- Ti Alloy Gr 2 Curved Spring Washer
- Titanium Gr 2 Countersunk Washer
- ASTM B348 Titanium Gr 2 Flat Washers
- Titanium Gr 2 Ogee Washer
- Titanium Gr 2 Spherical Washer
- ASME SB348 Titanium Gr 2 Fender Washer
- Titanium Alloy Gr 2 Hex Washers
- Titanium Gr 2 Fender Washers
- Titanium Gr 2 Tab Washers
- Ti Alloy Gr 2 Round Washer
- Ti Alloy Gr 2 Tab Washer Manufacturer
- DIN 3.7035 Countersunk Washer
- Titanium Alloy Gr 2 Industrial Washers
- Titanium Gr 2 Fender Washer
- Titanium Alloy Gr 2 Washer
- Titanium Gr 2 Dock Washer Stockholder
Titanium Gr 2 Washers Chemical Composition
| Grade | Ti | C | Fe | H | N | O |
| Ti Grade2 | 99.2 min | 0.1 max | 0.3 max | 0.015 max | 0.03 max | 0.25 max |
Titanium Gr 2 Washers Mechanical Properties
| Element | Density | Melting Point | Tensile Strength | Yield Strength (0.2%Offset) | Elongation |
| Titanium Gr 2 | 4.5 g/cm3 | 1665 °C (3030 °F) | Psi – 49900 , MPa – 344 | Psi – 39900 , MPa – 275 | 20 % |
